| 1984-1996 Corvette Differentials
Dana 44 HD, Dana 36 and Heavy Duty Dana 36
Re manufactured with New Gear Sets & Custom Built Differentials
Also see our Corvette Differential Ring & Pinion Section
Differentials carry a 4 year warranty that includes 'no gear noise'.
All Dana 44 differentials are available with any of our Ring & Pinion
Ratios: 3.07, 3.33, 3.54, 3.54 w/7/16" ring gear bolts,
3.73, 3.73 w/ 7/16" ring bolts,
3.90 w/ 7/16"ring bolts,
4.10, 4.56 w/ 3/8" & 7/16" ring bolts,
4.88 w/ 3/8" & 7/16" ring bolts.
DANA-44HD RE-MANUFACTURED Custom units with Limited 4 year warranty (same ratio).
$495.00 With Core In. Includes:
NEW Bearings (6), Seals (3), Trac-Loc Clutch Pack with Retainers, Cross Shaft and Spider
Gear thrust Washers, Ring Gear Bolts, Pinion Flange Retaining Nut, Shims.
DANA-44HD WITH NEW NITRO RING & PINION Built to order
Re-manufacturer WITH NEW RING & PINION From $790.00 w/exchange*
See Dana 44HD New Gear selection listed above.
DANA 44 conversion to any of our 10 ratios, 3.07; 3.45; 3.54 are stock, all other ratios are
special order and are not returnable for refund, In House Credit Only. Available as stock with
factory heat treat or special heat treatments for greatly improved longevity in
performance use. Differential Cores must be returned within three weeks of recite
of order to qualify for any refund.
Custom Built Positractions
We offer a complete selection of assembled posi's, modified posi's, clutches, spiders, internal
kits, empty standard or polished posi cases, posi internal kits. Our high performance units
receive our special heat-treated gears and cross shaft to resist breakage.
Custom Built. Call for prices.
NEW Dana 44 Trac-Loc Positractions $365.00
This is a Complete New Dana HD Trac-Loc for 1984-1996 Dana 44HD
NEW TRUETRAC HEAVY DUTY POSITRACTION
D 44HD VETTE C4 & VIPER $879.61
NEW POSI'S CARRY A 2 YEAR WARRANTY !
3RD Member Bearing and Seal Sets Dana 44HD.
Includes Timken pinion bearings & races,CR front seal, carrier side bearings & races, side axle
bearings and CR side seals, pinion nut, posi case shims ( pre-load and back-lash), Ring gear
bots, crush sleeve, pinion pre-load shims,(early and late differential) pinion depth shims,
marking compound, and Loc-Tite.
NEW CORVETTE DIFFERENTIAL SIDE AXLES DANA-44HD (manual)
Standard factory axles for standard driving. Also special heat-treated axles for those
who are rough on their rear.
Must specify left or right-hand axle.
Stock . Core $50.00 each.
DANA 36 1984-1996 and Heavy Duty Dana 36
DANA-36 STOCK AND MODIFIED are Custom Built, Heavy Duty Parts
available, Special Heat Treats, Stress Relieving, Modified Positractions.
$489.00 for a standard Rebuild of your core. Includes everything listed
below for the gear conversion except for a New Ring & Pinion
DANA-36 RE-MANUFACTURED WITH GEAR CONVERSION
(RATIO CHANGE) $890.00 Exchange* New Gear sets available: 2.59, 2.72, 3.07, 3.54,
3.73. Includes Timken Bearings (6), CR Seals (3), Dana Positraction Clutch Pack with
retainers, Cross Shaft, Ring Gear Bolts, Pinion Nut, shims and spacers as required.
Our Heavy Duty Dana 36 INCLUDES Timken Bearings, Housing completely
De-burred and Stress Relieved, Off-Set Heat Treated Nitro Ring & Pinion
and CNC Pre-Lapped, HD Pinion Flange, Blueprinted Positraction with
Dana Clutch Packs, Available with or without side axles or rear cover.
$ 1280.00 with side axles and rear cover.
ALL DIFFERENTIALS CARRY A 4 YEAR LIMITED WARRANTY, UNLIMITED MILEAGE AND 'WITH
NO GEAR NOISE' against defects in materials and workmanship.
NEW Dana 36 Trac-Loc Positractions $694.00
COMPLETE NEW HEAVY DUTY DANA 36 POSITRACTIONS
DRIVELINE, SUSPENSION and STEERING and RELATED PARTS
OUTER DRIVE SPINDLE
HEAVY DUTY REAR WHEEL BEARING AND HUB ASSEMBLIES
Made in the U.S.A. Forged Housing, tapered Bearings for much higher load
capacity than stock ball bearings.
1984-90 FRONT $179.00*
1984-96 REAR $149.00
1991-96 Front with Plug In $369.00
*Will fit 1986-90 if you elect not to use ABS system.
Wheel bearing assembly is pre-assembled and ready to install.
Re-manufactured Rack & Pinion
5 Year Warranty on the Re-manufactured Rack & Pinion sets.
1984-1985 Standard Code WL** $224.00
1984-1985 Standard Code YM** $224.00
1984-1985 Sports Steering H.D. Code AJ, AK, YP** $224.00
1986-1987 Standard Code CA, WU, WL** $224.00
1988 with 16" Wheels** $224.00
1988 with 17" Wheels** $224.00
1988 Code NS** $224.00
1989 Code FH** $224.00
1990-1992 All** $224.00
1993-1996 All** $224.00
**w/exchange or add $180.00 for core charge.
1984-1996 Suspension Components
REAR SUSPENSION PARTS:
A. Differential Cover, Auto $190.00
A. Differential Cover, Man. $895.00
B. Rear Support Housing, LH $135.00
B. Rear Support Housing, RH $135.00
C. Caliper Mount Plate, LH 1988-96 $39.00
C. Caliper Mount Plate, RH 1988-96 $39.00
C. 1984 Caliper Mount L or R $135.00
C. 1985-87 Caliper Mount L or R $135.00
D. Wheel Spindle, LH $149.00
D. Wheel Spindle, RH $149.00
E. Wheel Spindle, control lower $64.00
E. Wheel Spindle, control upper $64.00
F. Axle Sht. Side w/o U-Jt., Auto $185.00
F. Axle Sht. Side w/o U-Jt., Man. $145.00
G. Toe Adjustment Assm. w/rods $259.00
1984-1996 Suspension Components
FRONT SUSPENSION PARTS:
H. 1984-87 Lower Ctrl. Arm w/ball jnt., LH or RH $239.00
H. 1988-96 Lower Ctrl. Arm w/ball jnt., LH or RH $239.00
I. 1984-87 Upper Ctrl. Arm w/ball jnt., LH or RH $298.00
I. 1988-96 Upper Ctrl. Arm w/ball jnt., LH or RH $298.00
J. 1984-87 Steering Knuckle, LH or RH $220.00
J. 1988-96 Steering Knuckle, LH or RH $220.00
Caliper Mounting Plate L or R $38.00
1984-87 Complete Front Suspension Corner Assembly Re-manufactured
1988-96 Complete Front Suspension Corner Assembly Re-manufactured
Suspension Motor Cradle only $389.00
PAYPAL for Secure Transactions
Prices subject to change without notice
Corvette C4 1984-1996 Differentials
561-572-5323 Email: firstname.lastname@example.org
PayPal for Secure Transactions
|Go to 1984-1996 Dana 36 &
Dana 44 ring & pinion
page. click here
|GO TO DANA 36 RING & PINION
GEAR SETS. click here
|D-44 HD SIDE AXLE
|Heavy Duty Dana 36 New